NT68676.2A(HDMI+DVI+VGA) LCD Controller board Kit for LED Panel 1366×768 LTN156AT35-T01

NT68676.2A(HDMI+DVI+VGA) LCD Controller Kit for LED Panel 1366×768 LTN156AT35-T01

This is a great set of easy-reassembling LCD controller kit which is used to turn a bare laptop LCD panel into a desktop/PC monitor. It will be a amazing that your bare LCD will be of good use, and no longer be a waste, plug&play kit, no need soldering.

Attention: If your lcd model number is not in the list below, please remember to contact us for suggestion, as we will send the default kit for this item as soon as possible after your payment. So if this kit is not suitable for your lcd at all, you will need to take the responsibility of the failure, hope for your understanding. If you can leave your lcd model number after ordering, It will of great appreciated for us. 🙂

This kit is for the lcd with below lcd model numbers:

LTN156AT35-T01

Beside this kit, you will need to prepare the VGA cable/DVI cable/HDMI cable and power adapter (Ouput 12V,4A — it is for small size lcd from 10.1inch to 19inch) yourself, If you want to buy the power adapter from us too, you can check this item click here.

LCD Controller Board M.NT68676.2A:

M.NT68676.2A is a monitor control board, which can support LED/LCD panels. It can support resolution up to 2048X1152.

M.NT68676.2A can synchronize with computer automatically. Synchronization requires the synchronous signal which horizontal and vertical sync are separated.

M.NT68676.2A can support dynamic contrast control, headphone input and digital volume control simultaneously.

Size of controller board: 139mmX58mmX17mm

LED LVDS Cable Specification:

Have a try and you will get great surprise!

Then, are you going to get this kit?

Important Steps to Process your order with this kit:

Step 1: Please provide your LCD panel model no. by sending us the ebay message before bidding this item, so that we can advise a right kit for your LCD. (Usually, the model no. can be found on a sticker on the back of the LCD panel. If needed, disassemble the plastic shell and you will find the sticker). If possible, please give us as more specification of your LCD as you can. Then wait for our reply.

Step 2: We will give you the reply as soon as possible after carefully selecting and testing the kit by our technical support, and then you can place the order, and pay for it. We will send the package via HongKong Post as soon as possible after cleared payment. (If you prefer express shipping, please contact us to pay additional shipping cost before payment.)

Step 3: Waiting for the package.

We will write corresponding program into the lcd controller board to match your LCD, so this kit will match against one very specific LCD Panel or others that have exactly the same specification. However, a programmer could help on different LCDs, that is, change the firmware of the LCD controller board by yourself. Be aware that different LVDS cables and Inverters will be needed to match different LCDs.

Notes:

1. Please make sure that your LCD is ok before bidding this item, else you will be responsible for the incompatibility.

2. If you concern much about resolution setting, please reconsider before bidding!

3. We will try our best to prepare the right kit for you, such as writing the corresponding program into the controller board, selecting the suitable LVDS cable and the suitable inverter. But as we don't have an LCD exactly as yours at hand, we can just test the controller with our own LCD. For yours, you need to test it yourself to check if it works well or not. As you know, there are so many LCDs with many varieties in the market, sometimes we can't promise the exact compatibility. Please consider it before bidding! However, we have gained many success in preparing the kit for our customers in real store. So why not have a try to get surprise!

4. If you are not specialized in electronics or have doubts in operation, please contact us for instruction, as we are not able to responsible for wrong operation.

5. After finishing the connecting, please don't rush to power on! First, use multi-meter to test whether the GND of the LCD is connected with the GND of the controller board. If not, please check the connection again. If yes, please test whether there is a short circuit between the red wires and black wires of the LVDS cable. If there is a short circuit, it means opposite connection or other errors. Any problem, please feel free to contact us. DIY needs a certain professional knowledge, please kindly take the responsibility of the risk. No metal contact is allowed when powering on the controller board, otherwise short circuit may occur, which may cause unavailability of the controller board.

American Friend cryalith's Raspberry PI Computer:

Australian Friend beyelka's Project:

Successful Example (rossg77 — an American friend's Project ):

Successful Example (radicalboy_fr — a French friend's Project ):

Successful Example (docpot2008 — a Canadian friend's Project ):

Malta Friend drac1977's Project:

USA Friend loafer_tingo's Project :

Instruction to connect the controller board to the LCD:

1. Take away the old inverter and old LVDS cable from the LCD panel.

2. Connect the new inverter and LVDS cable to your LCD panel.

3. Connect controller board with PC by VGA cable/HDMI Cable/DVI cable.

4. Input power of 12V,4A. ( Please don't revised the voltage jumper setting on the lcd controller board before confirmation from us, because wrong revising of this voltage will get your lcd burnt. By the way, please don't connect the lvds cable wrongly, some wrong connecton can get your lcd burnt too, if you are not sure, please feel free to contact us.)

Package Include:

• 1 X LCD Controller Board (M.NT68676.2A) programmed for LTN156AT35-T01
• 1 X 5 keys Keypad with cable
• 1 X 25cm LVDS cable for LTN156AT35-T01

If your lcd is not in the list , please remember to contact us with lcd model number, so that we can introduce you a right kit.